Surface treatment

In addition to classic painting, various aids such as oils, rust activators, browning, and much more can significantly expand the design options.

This allows special accents to be set and opens up new design possibilities.

Zinc cleaner "Forte"

00601495

Special cleaner for galvanized surfaces Characteristics: especially suitable for galvanized surfaces ensures ideal adhesion of paint or varnish prevents the paint from peeling off prematurely optimal brightening of old zinc surfaces extreme cleaning power for heavy dirt highly concentrated - long range Removes rust stains, soot, grease, and much more. It is an acidic concentrate for cleaning hot-dip and galvanized surfaces. It removes flux residues and oxidation products such as rust stains, has an active cleaning effect and removes dirt, soot, grease and oil. It passivates and phosphates so that paints adhere better. This process prevents the paint from peeling off prematurely. Application: Dilute the zinc cleaner in a ratio of 1:10 to 1:20 with cold water. Then apply with a brush or brush to the surface to be cleaned, Leave on for about 5 minutes and rinse with clean water. If the soiling is very severe, the process must be repeated. Dry well after cleaning. Notice: Zinc Cleaner Forte must not come into contact with acid-sensitive materials such as marble. When cleaning, always proceed gradually to prevent drying during the exposure time. Carry out a preliminary test in a hidden location.

From €11.90*

Black finishing (Ballistol)

00622100

guarantees permanent and wear-resistant browning Please note that this black finishing does not work on steel containing more than 3% Chromium. Proceed like this: the workpiece has to be degreased carefully (e.g. with our Cold Degreaser). Then apply black finishing by means of a dropper or brush on the parts to be browned. Allow to react for say 3 minutes until a yellow-whitish cover forms. Then wash it off with water, dry it by dabbing with a soft cloth and spray BALLISTOL on it. Ready!</i>

From €12.90*

Black finishing

00622103

guarantees permanent and wear-resistant browning Please note that this black finishing does not work on steel containing more than 3% Chromium. Coverage (rough guideline): 10m²/l Proceed like this: the workpiece has to be degreased carefully (e.g. with our Cold Degreaser). Then apply black finishing by means of a dropper or brush on the parts to be browned. Allow to react for say 3 minutes until a yellow-whitish cover forms. Then wash it off with water, dry it by dabbing with a soft cloth and spray BALLISTOL on it. Ready!

From €15.90*

Fluid for degreasing

00622104

fluid for degreasing, aerosol Oil and grease are removed from metallic surfaces, even persistent remainders of grease and resin will disappear without any problems. Ideal as a preliminary treatment to the browning process with our black finishing. Application: Depending on the degree of oiliness, spray several times onto the part to be degreased and then wipe off. Finally, spray the grease-free area again. After drying, the area is free of grease, and the subsequent treatment can now be carried out.

Content: 0.05 Liter (€0.00* / 1 Liter)

From €4.20*

black finishing set

00622108

guarantees permanent and wear-resistant browning Set consists of - Cold Degreaser spray 50 ml - Quickbrowning 50 ml - Ballistol spray 50 ml - 2 pair nitrilic gloves - 2 brushes - 2 lintless clothes Please note that this black finishing does not work on steel containing more than 3% Chromium. Proceed like this: the workpiece has to be degreased carefully (e.g. with our Cold Degreaser). Then apply black finishing by means of a dropper or brush on the parts to be browned. Allow to react for say 3 minutes until a yellow-whitish cover forms. Then wash it off with water, dry it by dabbing with a soft cloth and spray BALLISTOL on it. Ready!

€29.95*

pcs

Black finishing for copper, brass and silver

00622107

guarantees permanent and wear-resistant browning Application: before application metals must be degreased. For application of Nerofor use a brush, smaller metal parts may also be dipped. After about two minutes exposure time the metal can be rinsed off with water. Afterwards dry the workpiece with a soft cotton cloth. To get a matte sheen you can spray the workpiece with Ballistol universal oil.

Content: 0.05 Liter (€0.00* / 1 Liter)

From €12.80*

Black finishing for aluminium

00622113

guarantees permanent and wear-resistant browning Application: before application metals must be degreased. For application use a brush, smaller metal parts may also be dipped. After about 30 seconds exposure time the metal can be rinsed off with water. Afterwards dry the workpiece with a soft cotton cloth. To get a matte sheen you can spray the workpiece with Ballistol universal oil. The bluing is very productive. About 100 ml is needed for one square meter.

Content: 0.05 Liter (€0.00* / 1 Liter)

From €18.90*

Tip

Wax - WAX

00622118

100% natural ingredients, for caring and preserving blades, wood, leather and much more, can with 60g content Properties: 100% natural ingredients handmade food safe easy to process easy to use suitable for wood, leather, metal, plastic preserves, protects, cares What is it used for? For the care and preservation of blades, handle materials, cutting boards, and much more. It prevents rust, keeps leather supple, protects wood and other materials and can be used for almost EVERYTHING. How is it used? 1. Clean part 2. Apply with a clean, dry cloth and work in evenly 3. Remove excess wax with a cloth 4. Repeat process if necessary

Content: 0.06 Kilogramm (€316.67* / 1 Kilogramm)

€19.00*

pcs

16.67 %

Tip

Blacksmith oil 1L

00622128

proofed and tested, special blend of 100% natural oils such as linseed and rapeseed oil. For “blackening” or preserving steel, wood, and much more. What is Blacksmith Oil? Our forge oil is a tried and tested, Special blend of 100% natural oils such as linseed and rapeseed oil. It can for “blackening” or preserving steel, wood, and much more. be used. Black coloring: When blackening, the workpiece is warmed slightly and then covered with a thin layer of oil. This is then held over a soot-free fire and slowly heated. This causes stuck-on carbon to decompose on the surface. First a brown, then a black, sticky color is created. This process can be repeated until the desired depth of coloring is achieved. This method protects the workpiece from corrosion. Suitable for all metals, copper, brass, bronze, and much more. Notice: The OIL can be applied with a brush or cloth. Shake the bottle well before use and close it properly after use. Photo 4 shows a grill fork blackened or burned black with blacksmith oil. The staining was created in 2 passes.

€10.00* €12.00*

pcs

Tip

OWATROL-oil

00622130

From €9.90*

Ballistol 50 ml

00622140

Spray

Content: 0.05 Liter (€61.80* / 1 Liter)

From €3.49*

Ballistol 50 ml

00622141

Spray

Content: 0.05 Liter (€73.00* / 1 Liter)

€3.65*

pcs

Ballistol 200 ml

00622142

Spray

Content: 0.2 Liter (€39.50* / 1 Liter)

€7.90*

pcs

11 %

Ballistol universal tissue dispenser box

00622145

with 130 resistant, highly absorbent viscose-containing towels

€25.80* €28.99*

pcs

Tip

Ballistol universal tissue

00622146

130 resistant, highly absorbent viscose-containing towels For refilling the Ballistol universal tissue dispenser box. Suitable for almost all liquid Ballistol products. Contents: 130 tissues, tissue size: 20 x 19 cm. Highly absorbent, very soft and low-linting Solvent resistant, tear resistant Antistatic, impact resistant Suitable for polishing and cleaning surfaces or hands in all areas Thanks to the viscose content it is more absorbent than conventional towels made from synthetic fibres Also suitable for disinfectants, non-drip, silicone, PTFE and acid-free

€14.90*

pcs

Tip

USTA Werkstatt-Öl, Spray 200 ml

00622147

USTA Werkstatt-Öl, Spray 200 ml

Content: 0.2 Liter (€27.45* / 1 Liter)

€5.49*

pcs

Tip

Pantarol® metal protection (indoor)

00622161

Pantarol® metal protection (indoor) #Varinfo colorless, pigment-free anti-corrosion paint based on synthetic resin NC for particularly high-quality, high-gloss protective coatings on metal surfaces Pretreatment: A grease, oil and dust-free, shiny metallic surface is required for the formation of a permanent protective film. Processing: Apply by brushing, spraying, dipping under the following conditions: Painting: The product is ready for painting Spraying: Prepare ready-to-spray with “Thinner for Pantarol®” No. 101 in a ratio of 2 parts paint and 1 part thinner. Recommended spray viscosity: 14-15 sec/4 mm DIN (20°C); advantageous spraying process at approx. 3-4 bar pressure with 1 mm nozzle. Dipping: If necessary, adjust the product with “Thinner for Pantarol®” No. 101 to a dipping viscosity of 18-22 sec/4mm DIN (20°C). Clean the tools immediately after use with “Thinner for Pantarol®” No. 101. Drying: Air drying: at 15-25°C dust dry after a few minutes; hand dry after approx. 30 minutes; completely dry after approx. 2 hours; depending on the layer thickness, ready for packaging after approx. 24 hours; oven drying: ventilate for approx. 10 minutes, baking temperature approx. 80-100°C (130°C must not be exceeded!), baking time approx. 25-30 minutes Yield: If the processing recommendations are followed, approx. 6 - 8 m² of treatment area per liter.

From €25.95*

Tip

Pantarol® A metal protection (outdoor)

00622164

Pantarol® A metal protection (outdoor) #Varinfo colorless, pigment-free anti-corrosion paint based on polyacrylate for weather-resistant, high-gloss protective coatings on metal surfaces (especially for non-ferrous metals). In order to ensure an elastic metal protective surface outdoors, Pantarol® A uses a resin that can follow the temperature movements of metals and is also UV stable. Pretreatment: A prerequisite for building up a permanent protective film is a grease, oil and dust-free, shiny metallic surface. Processing: Apply by brushing or spraying under the following conditions: Painting: The product is ready to brush Spraying: Prepare ready to spray with “Thinner for Pantarol® A” No. 131 in a ratio of 2 parts paint and 1 part thinner. Recommended spray viscosity: 15 sec/4 mm DIN (20 °C); at approx. 3-4 bar pressure with a 0.8-1 mm nozzle. Rollers: An additive is required for roller application to prevent threads from pulling. Clean the tools immediately after use with “Thinner for Pantarol® A” No. 131. Drying: Air drying: at 15 - 25°C Dust dry after approx. 15 minutes, hand dry after approx. 30 - 45 Completely dry after approx. 24 hours Oven drying: Completely dry after approx. 1 - 2 hours at elevated temperature (40 - 60°C; up to max. 100°C) Yield: If the processing recommendations are followed, approx. 8-12 m² of treatment area per liter.

From €28.80*

Tip

Pantarol® Special thinner

00622165

Pantarol® Special thinner Special thinner for Pantarol metal protection to achieve a homogeneous surface when spraying.

From €18.80*

Metallic Primer

00622209

Content: 0.473 Liter (€0.00* / 1 Liter)

From €9.90*

Iron Reactive Paint

00622218

Content: 0.1 Liter (€0.00* / 1 Liter)

From €16.01*

Rust Activator

00622239

Because not all rust is created equal! Our rust activator is an aqueous liquid that can be used to create a genuine rusty surface on ferrous metal surfaces within a few hours. It is not a paint or other coating designed to simulate the appearance of rust, but rather a genuine chemical oxidation process. The activator can be applied by brush, roller, natural sponge, or spray. Unlike other methods using hydrochloric acid or other household remedies, it is less aggressive, significantly more efficient, and ensures a uniform texture. Properties: ⦁ Easy to use ⦁ Safe application ⦁ Even surface ⦁ Natural rust appearance ⦁ Rapid rusting ⦁ High yield Application: The ideal application temperature is between 13°C and 29°C. (If the surface is too cold or too warm, the rusting process will slow down.) Apply a test surface to check adhesion, compatibility, and results. 1) Remove scale and grease from the surface. 2) Spray the rust activator onto the metal surface to be rusted. 3) Spray again after 5-10 minutes. To avoid drip marks, apply the rust activator from the bottom up. Use a damp sponge and gently dab the surface to remove excess. Then allow the surface to dry completely. Wear gloves and safety goggles! Not suitable for stainless steel! Post-treatment: Post-treatment can easily be carried out with Owatrol oil. The rust layer should be "consolidated" for this. Coverage: approx. 10-15 sqm/liter per coat. Please note the hazard and safety information.

Content: 0.1 Liter (€0.00* / 1 Liter)

€27.00*

Blacking

00622300

Care product for cast-iron parts Blacking gives the cast iron or iron metals of ovens or grills an appearance like new again. Protects cast-iron and metal parts and inserts of stoves, ovens or grills. cream-like simple to apply with a cloth gives cast iron a natural patina-like appearance odourless Very effective, the cream is applied in small quantities over the entire surface. Polish with a dry cloth.

Content: 0.1 Liter (€0.00* / 1 Liter)

From €7.20*

Silicone spray 200 ml

51103020

Content: 0.2 Liter (€30.00* / 1 Liter)

€6.00*

pcs