for Kuhn 2000K/CF 40 and CF 50 cylinders suitable from cylinder production date 02/2026 consisting of all wear seals   ATTENTION: Not suitable for Parker "DS160" cylinder units - before 03/2026

  for Kuhn 2000K/CF 40 and CF 50 cylinders suitable from cylinder production date 02/2026 consisting of cylinder head with pressed-in guide bushing   The brass guide bushing is not available separately.   ATTENTION: Not suitable for Parker "DS160" cylinder units - before 03/2026

  for Kuhn 2000K/CF 40 and CF 50 cylinders Suitable for cylinder production year 02/2026 and predecessor models     ATTENTION: Not suitable for Parker "DS160" cylinder units - before 03/2026

  suitable for swivel fork head suitable from cylinder production date 02/2026     ATTENTION: Not suitable for Parker "DS160" cylinder units - before 03/2026

  for Kuhn airhammer K 12/42 und K24/53 with one outlet   Note: observe the direction of rotation

  for Kuhn airhammer K 12/42 und K24/53 with two outlets   Note: observe the direction of rotation

  for Kuhn airhammer K-0, KB-1 und K-23 height approx. 90 mm, volumen approx. 40 ml

  for Kuhn airhammer K-0, KB-1 und K-23

  for Kuhn airhammer K-CF   Technical specifications: Volume (ml): 150 Flow rate (cm³/stroke): 0.5 Media: Oil, petroleum, aerosols and oils with additives Housing: steel, powder-coated Mouthpiece: pointed and hollow/universal mouthpiece Connection thread: for tapered and ball grease nipples, DIN 71412, DIN 3402, for funnel type grease nipples, DIN 3405 Maximum pressure (bar): 150 Dimensions ØxL (mm): 40 x 230 Weight (kg): 0.25

  Filling nipple (FN), M 10 x 1 male 400 g grease cartridge, DIN 1284, grease filling system or loose grease using a spatula   The grease gun for eternity!   Specification Filling nipple (FN), M 10 x 1 male Polybag, with headcard, for hanging display High pressure hose, M 10 x 1 male, 11 x 300 mm, with 4-claws-coupler, M 10 x 1 female   Special notes Operates with greases up to NLGI grade 2 at 20°C Plunger with exactly fitting when using bulk grease or cartridge Due to the flexibility of the push rod, the plunger can be inserted into damaged cartridges or cartridges not exactly matching the standard dimensions acc. to DIN 1283 TÜV - certified Pump piston, cylinder and O-ring with 6 μ fit (no dummy lubrication) No dummy (apparent) lubrication. Sealing system: O-ring and ball valve prevent grease compressed in the grease gun head from feeding back. Performance unchanged after 40.000 actuating cycles Separate filling and ventilation valves on grease gun head Grease gun head, zinc die casting Z 410 Sure grip handling due to deep band knurls Safe handle on the push rod Slip resistant handle on grease gun lever Enables even under extreme backpressure, a variable lubrication pressure with steady effort applied Allows lubrication in difficult to reach locations because the smallest lever operation results in grease being pumped reliably to the lubrication point. Plunger rod clamp on end cap enables manual pressure to be applied to spring to compress bulk grease, or to force in the plunger in damaged cartridges. Push rod can be locked in any position - push rod does not have to be fully retracted to release the spring pressure on the grease (grease does not saponify) High-speed ventilation, by half a rotation of the grease gun tube

  for Kuhn air hammer set of 3 pieces

  for Kuhn air hammer set of 4 pieces

  for Kuhn air hammer set of 2 pieces

  for Kuhn air hammer set of 4 pieces, each 1800 mm

  for Kuhn air hammer set of 5 pieces

  for Kuhn air hammer set of 5 pieces

  for front cylinder of Kuhn airhammers type K 0 set of 3 or 4 pieces, diameter 150 mm   For the front cylinder of type K 0 you need one set

  for rear cylinder of Kuhn airhammers type K 0 set of 3 or 4 pieces, diameter 160 mm   For the rear cylinder of type K 0 you need two sets

  for front cylinder of Kuhn airhammers type KB1, K2 and K23, set of 3 or 4 pieces, diameter 170 mm   For the front cylinder of type KB 1 you need one set , for K2 or K 23 you need two sets

  for Kuhn air hammer for rear cylinder, set of 3 or 4 pieces, diameter 185 mm   You need two sets.

  for front cylinder of Kuhn airhammers type K3 diameter 250 mm, t=6 mm   For the front cylinder of type K3 you need two pieces

  for rear cylinder of Kuhn airhammers type K3 diameter 270 mm, t=6 mm   For the rear cylinder of type K3 you need two pieces

  for Kuhn air hammer 22 kg for front cylinder, set of 3 or 4 pieces, diameter 130 mm