guarantees permanent and wear-resistant browning   Set consists of - Cold Degreaser spray 50 ml - Quickbrowning 50 ml - Ballistol spray 50 ml - 2 pair nitrilic gloves - 2 brushes - 2 lintless clothes   Please note that this black finishing does not work on steel containing more than 3% Chromium.   Proceed like this: the workpiece has to be degreased carefully (e.g. with our Cold Degreaser). Then apply black finishing by means of a dropper or brush on the parts to be browned. Allow to react for say 3 minutes until a yellow-whitish cover forms. Then wash it off with water, dry it by dabbing with a soft cloth and spray BALLISTOL on it. Ready!

  guarantees permanent and wear-resistant browning   Copper, brass, and bronze acquire a black surface through this treatment; this process is also known as blackening. Silver also acquires a black surface through this treatment.   Depending on the exposure time, the intensity of the color can be varied from brown to dark brown to black. This is particularly useful when creating an elegant, antique-looking finish.   Ideal for creating an "antique" look for all non-ferrous metals Color depth can be individually determined by the exposure time PTFE- and silicone-free   Application:   1. Pretreatment   The parts to be colored must be thoroughly degreased and free of any oxidation. First, pretreat with fine steel wool or sandpaper (maximum 380 grit). Then degrease the workpiece (we recommend Ballistol Cold Degreaser) or treat it with 30% hydrochloric acid. Finally, rinse thoroughly with warm water.   2. Application   Application depends on the size of the area to be treated: apply with a brush, spray, or by immersion.   The ideal immersion temperature is approximately 30–35 °C. A lower temperature slows down the process and thus extends the reaction time. Caution: The immersion temperature must not exceed 40 °C. The immersion time is approximately 1 to 3 minutes. Depending on the desired tint, the workpiece should be immersed for a shorter or longer time.   3. Aftercare   First, rinse the workpiece with fresh water after application. Then, wipe off any water with a dry cloth or rag and apply a clear varnish, wax, or oil for a clean finish.   Want to achieve a lighter shade?   Color variations by dilution up to 1:4 The bluing agent can be diluted with water up to a mixing ratio of 1:4. The more water, the browner the color. The less water, the darker the color. Applying pure results in a black coloration on most non-ferrous metals.

  guarantees permanent and wear-resistant browning   Application: before  application metals must be degreased. For application use a brush, smaller metal parts may also be dipped. After about 30 seconds exposure time the metal can be rinsed off with water. Afterwards dry the workpiece with a soft cotton cloth. To get a matte sheen you can spray the workpiece with Ballistol universal oil.   The bluing is very productive. About 100 ml is needed for one square meter.

  100% natural ingredients, for caring and preserving blades, wood, leather and much more, can with 60g content   Properties: 100% natural ingredients handmade food safe easy to process easy to use suitable for wood, leather, metal, plastic preserves, protects, cares   What is it used for? For the care and preservation of blades, handle materials, cutting boards, and much more. It prevents rust, keeps leather supple, protects wood and other materials and can be used for almost EVERYTHING.   How is it used? 1. Clean part 2. Apply with a clean, dry cloth and work in evenly 3. Remove excess wax with a cloth 4. Repeat process if necessary

  proofed and tested, special blend of 100% natural oils such as linseed and rapeseed oil. For “blackening” or preserving steel, wood, and much more.   What is Blacksmith Oil? Our forge oil is a tried and tested, Special blend of 100% natural oils such as linseed and rapeseed oil. It can for “blackening” or preserving steel, wood, and much more. be used.   Black coloring: When blackening, the workpiece is warmed slightly and then covered with a thin layer of oil. This is then held over a soot-free fire and slowly heated. This causes stuck-on carbon to decompose on the surface. First a brown, then a black, sticky color is created. This process can be repeated until the desired depth of coloring is achieved. This method protects the workpiece from corrosion. Suitable for all metals, copper, brass, bronze, and much more.   Notice: The OIL can be applied with a brush or cloth. Shake the bottle well before use and close it properly after use.     Photo 4 shows a grill fork blackened or burned black with blacksmith oil. The staining was created in 2 passes.

Ballistol® Universalöl   Note: The mixture is classified as non-hazardous within the meaning of Regulation (EC) No. 1272/2008 [CLP].

Ballistol® 50 ml Spray Universal oil – uniquely versatile and environmentally friendly: - Cares for, lubricates, disinfects, protects against rust - Penetrates into the smallest corners, provides excellent lubrication, does not resinify, and is completely biodegradable. - Food-safe, skin-friendly, and completely harmless   BALLISTOL® Universal Oil is free of silicone, PTFE, acids, and resins, and does not resinify.

Ballistol® 200 ml Spray Universal oil – uniquely versatile and environmentally friendly: - Cares for, lubricates, disinfects, protects against rust - Penetrates into the smallest corners, provides excellent lubrication, does not resinify, and is completely biodegradable. - Food-safe, skin-friendly, and completely harmless   BALLISTOL® Universal Oil is free of silicone, PTFE, acids, and resins, and does not resinify.

Ballistol® universal tissue dispenser box with 130 resistant, highly absorbent viscose-containing towels

Ballistol® universal tissue 130 resistant, highly absorbent viscose-containing towels   For refilling the Ballistol universal tissue dispenser box. Suitable for almost all liquid Ballistol products. Contents: 130 tissues, tissue size: 20 x 19 cm.   Highly absorbent, very soft and low-linting Solvent resistant, tear resistant Antistatic, impact resistant Suitable for polishing and cleaning surfaces or hands in all areas   Thanks to the viscose content it is more absorbent than conventional towels made from synthetic fibres Also suitable for disinfectants, non-drip, silicone, PTFE and acid-free

  cleans and maintains, lubricates and protects against rust, silicone-, PTFE-, acid- and resin-free, and does not gum up

Pantarol® metal protection (indoor)  #Varinfo colorless, pigment-free anti-corrosion paint based on synthetic resin NC for particularly high-quality, high-gloss protective coatings on metal surfaces   Pretreatment: A grease, oil and dust-free, shiny metallic surface is required for the formation of a permanent protective film.   Processing: Apply by brushing, spraying, dipping under the following conditions: Painting: The product is ready for painting Spraying: Prepare ready-to-spray with “Thinner for Pantarol®” No. 101 in a ratio of 2 parts paint and 1 part thinner. Recommended spray viscosity: 14-15 sec/4 mm DIN (20°C); advantageous spraying process at approx. 3-4 bar pressure with 1 mm nozzle. Dipping: If necessary, adjust the product with “Thinner for Pantarol®” No. 101 to a dipping viscosity of 18-22 sec/4mm DIN (20°C).   Clean the tools immediately after use with “Thinner for Pantarol®” No. 101.   Drying: Air drying: at 15-25°C dust dry after a few minutes; hand dry after approx. 30 minutes; completely dry after approx. 2 hours; depending on the layer thickness, ready for packaging after approx. 24 hours; oven drying: ventilate for approx. 10 minutes, baking temperature approx. 80-100°C (130°C must not be exceeded!), baking time approx. 25-30 minutes   Yield: If the processing recommendations are followed, approx. 6 - 8 m² of treatment area per liter.

Pantarol® A metal protection (outdoor)  #Varinfo colorless, pigment-free anti-corrosion paint based on polyacrylate for weather-resistant, high-gloss protective coatings on metal surfaces (especially for non-ferrous metals).   In order to ensure an elastic metal protective surface outdoors, Pantarol® A uses a resin that can follow the temperature movements of metals and is also UV stable.   Pretreatment: A prerequisite for building up a permanent protective film is a grease, oil and dust-free, shiny metallic surface.   Processing: Apply by brushing or spraying under the following conditions: Painting: The product is ready to brush Spraying: Prepare ready to spray with “Thinner for Pantarol® A” No. 131 in a ratio of 2 parts paint and 1 part thinner. Recommended spray viscosity: 15 sec/4 mm DIN (20 °C); at approx. 3-4 bar pressure with a 0.8-1 mm nozzle. Rollers: An additive is required for roller application to prevent threads from pulling.   Clean the tools immediately after use with “Thinner for Pantarol® A” No. 131.   Drying: Air drying: at 15 - 25°C Dust dry after approx. 15 minutes, hand dry after approx. 30 - 45 Completely dry after approx. 24 hours Oven drying: Completely dry after approx. 1 - 2 hours at elevated temperature (40 - 60°C; up to max. 100°C)   Yield: If the processing recommendations are followed, approx. 8-12 m² of treatment area per liter.

Pantarol® Special thinner Special thinner for Pantarol metal protection to achieve a homogeneous surface when spraying.

  Because not all rust is created equal!   Our rust activator is an aqueous liquid that can be used to create a genuine rusty surface on ferrous metal surfaces within a few hours. It is not a paint or other coating designed to simulate the appearance of rust, but rather a genuine chemical oxidation process. The activator can be applied by brush, roller, natural sponge, or spray. Unlike other methods using hydrochloric acid or other household remedies, it is less aggressive, significantly more efficient, and ensures a uniform texture.   Properties: ⦁ Easy to use ⦁ Safe application ⦁ Even surface ⦁ Natural rust appearance ⦁ Rapid rusting ⦁ High yield   Application: The ideal application temperature is between 13°C and 29°C. (If the surface is too cold or too warm, the rusting process will slow down.) Apply a test surface to check adhesion, compatibility, and results. 1) Remove scale and grease from the surface.   2) Spray the rust activator onto the metal surface to be rusted.   3) Spray again after 5-10 minutes.   To avoid drip marks, apply the rust activator from the bottom up. Use a damp sponge and gently dab the surface to remove excess.   Then allow the surface to dry completely.   Wear gloves and safety goggles!   Not suitable for stainless steel!   Post-treatment: Post-treatment can easily be carried out with Owatrol oil. The rust layer should be "consolidated" for this.   Coverage: approx. 10-15 sqm/liter per coat.   Please note the hazard and safety information.

  Care product for cast-iron parts   Blacking gives the cast iron or iron metals of ovens or grills an appearance like new again. Protects cast-iron and metal parts and inserts of stoves, ovens or grills.   cream-like simple to apply with a cloth gives cast iron a natural patina-like appearance odourless   Very effective, the cream is applied in small quantities over the entire surface. Polish with a dry cloth.

  suitable for AN-15 or other air and spring hammers   These damping mats provide a technically clean decoupling of air forging or spring hammers. They are made of a special polyurethane elastomer and are mounted between the steel base and the workshop floor.   Features: Clean decoupling of the machine Significantly reduced emissions Improved smooth running Increased machine service life Durable material Easy to attach (glue) Quickly improve the installation situation   Several strips are required to store the air hammer. These are glued under the steel base with polyurethane adhesive or simply placed underneath. We recommend: Base unfilled: 2 strips Base filled with concrete: 3 strips Base filled with reinforced concrete: 4 strips

  suitable for AN-25 or other air and spring hammers   These damping mats provide a technically clean decoupling of air forging or spring hammers. They are made of a special polyurethane elastomer and are mounted between the steel base and the workshop floor.   Features: Clean decoupling of the machine Significantly reduced emissions Improved smooth running Increased machine service life Durable material Easy to attach (glue) Quickly improve the installation situation   Several strips are required to store the air hammer. These are glued under the steel base with polyurethane adhesive or simply placed underneath. We recommend: Base unfilled: 2 strips Base filled with concrete: 3 strips Base filled with reinforced concrete: 4 strips

  suitable for AN-40 or other air and spring hammers   These damping mats provide a technically clean decoupling of air forging or spring hammers. They are made of a special polyurethane elastomer and are mounted between the steel base and the workshop floor.   Features: Clean decoupling of the machine Significantly reduced emissions Improved smooth running Increased machine service life Durable material Easy to attach (glue) Quickly improve the installation situation   Several strips are required to store the air hammer. These are glued under the steel base with polyurethane adhesive or simply placed underneath. We recommend: Base unfilled: 2 strips Base filled with concrete: 3 strips Base filled with reinforced concrete: 4 strips

  suitable for AN-55 or other air and spring hammers   These damping mats provide a technically clean decoupling of air forging or spring hammers. They are made of a special polyurethane elastomer and are mounted between the steel base and the workshop floor.   Features: Clean decoupling of the machine Significantly reduced emissions Improved smooth running Increased machine service life Durable material Easy to attach (glue) Quickly improve the installation situation   Several strips are required to store the air hammer. These are glued under the steel base with polyurethane adhesive or simply placed underneath. We recommend: Base unfilled: 2 strips Base filled with concrete: 3 strips Base filled with reinforced concrete: 4 strips