Ballistol® 200 ml Spray Universal oil – uniquely versatile and environmentally friendly: - Cares for, lubricates, disinfects, protects against rust - Penetrates into the smallest corners, provides excellent lubrication, does not resinify, and is completely biodegradable. - Food-safe, skin-friendly, and completely harmless   BALLISTOL® Universal Oil is free of silicone, PTFE, acids, and resins, and does not resinify.

Ballistol® universal tissue dispenser box with 130 resistant, highly absorbent viscose-containing towels

Ballistol® universal tissue 130 resistant, highly absorbent viscose-containing towels   For refilling the Ballistol universal tissue dispenser box. Suitable for almost all liquid Ballistol products. Contents: 130 tissues, tissue size: 20 x 19 cm.   Highly absorbent, very soft and low-linting Solvent resistant, tear resistant Antistatic, impact resistant Suitable for polishing and cleaning surfaces or hands in all areas   Thanks to the viscose content it is more absorbent than conventional towels made from synthetic fibres Also suitable for disinfectants, non-drip, silicone, PTFE and acid-free

  cleans and maintains, lubricates and protects against rust, silicone-, PTFE-, acid- and resin-free, and does not gum up

Pantarol® metal protection (indoor)  #Varinfo colorless, pigment-free anti-corrosion paint based on synthetic resin NC for particularly high-quality, high-gloss protective coatings on metal surfaces   Pretreatment: A grease, oil and dust-free, shiny metallic surface is required for the formation of a permanent protective film.   Processing: Apply by brushing, spraying, dipping under the following conditions: Painting: The product is ready for painting Spraying: Prepare ready-to-spray with “Thinner for Pantarol®” No. 101 in a ratio of 2 parts paint and 1 part thinner. Recommended spray viscosity: 14-15 sec/4 mm DIN (20°C); advantageous spraying process at approx. 3-4 bar pressure with 1 mm nozzle. Dipping: If necessary, adjust the product with “Thinner for Pantarol®” No. 101 to a dipping viscosity of 18-22 sec/4mm DIN (20°C).   Clean the tools immediately after use with “Thinner for Pantarol®” No. 101.   Drying: Air drying: at 15-25°C dust dry after a few minutes; hand dry after approx. 30 minutes; completely dry after approx. 2 hours; depending on the layer thickness, ready for packaging after approx. 24 hours; oven drying: ventilate for approx. 10 minutes, baking temperature approx. 80-100°C (130°C must not be exceeded!), baking time approx. 25-30 minutes   Yield: If the processing recommendations are followed, approx. 6 - 8 m² of treatment area per liter.

Pantarol® A metal protection (outdoor)  #Varinfo colorless, pigment-free anti-corrosion paint based on polyacrylate for weather-resistant, high-gloss protective coatings on metal surfaces (especially for non-ferrous metals).   In order to ensure an elastic metal protective surface outdoors, Pantarol® A uses a resin that can follow the temperature movements of metals and is also UV stable.   Pretreatment: A prerequisite for building up a permanent protective film is a grease, oil and dust-free, shiny metallic surface.   Processing: Apply by brushing or spraying under the following conditions: Painting: The product is ready to brush Spraying: Prepare ready to spray with “Thinner for Pantarol® A” No. 131 in a ratio of 2 parts paint and 1 part thinner. Recommended spray viscosity: 15 sec/4 mm DIN (20 °C); at approx. 3-4 bar pressure with a 0.8-1 mm nozzle. Rollers: An additive is required for roller application to prevent threads from pulling.   Clean the tools immediately after use with “Thinner for Pantarol® A” No. 131.   Drying: Air drying: at 15 - 25°C Dust dry after approx. 15 minutes, hand dry after approx. 30 - 45 Completely dry after approx. 24 hours Oven drying: Completely dry after approx. 1 - 2 hours at elevated temperature (40 - 60°C; up to max. 100°C)   Yield: If the processing recommendations are followed, approx. 8-12 m² of treatment area per liter.

Pantarol® Special thinner Special thinner for Pantarol metal protection to achieve a homogeneous surface when spraying.

  Because not all rust is created equal!   Our rust activator is an aqueous liquid that can be used to create a genuine rusty surface on ferrous metal surfaces within a few hours. It is not a paint or other coating designed to simulate the appearance of rust, but rather a genuine chemical oxidation process. The activator can be applied by brush, roller, natural sponge, or spray. Unlike other methods using hydrochloric acid or other household remedies, it is less aggressive, significantly more efficient, and ensures a uniform texture.   Properties: ⦁ Easy to use ⦁ Safe application ⦁ Even surface ⦁ Natural rust appearance ⦁ Rapid rusting ⦁ High yield   Application: The ideal application temperature is between 13°C and 29°C. (If the surface is too cold or too warm, the rusting process will slow down.) Apply a test surface to check adhesion, compatibility, and results. 1) Remove scale and grease from the surface.   2) Spray the rust activator onto the metal surface to be rusted.   3) Spray again after 5-10 minutes.   To avoid drip marks, apply the rust activator from the bottom up. Use a damp sponge and gently dab the surface to remove excess.   Then allow the surface to dry completely.   Wear gloves and safety goggles!   Not suitable for stainless steel!   Post-treatment: Post-treatment can easily be carried out with Owatrol oil. The rust layer should be "consolidated" for this.   Coverage: approx. 10-15 sqm/liter per coat.   Please note the hazard and safety information.

  Care product for cast-iron parts   Blacking gives the cast iron or iron metals of ovens or grills an appearance like new again. Protects cast-iron and metal parts and inserts of stoves, ovens or grills.   cream-like simple to apply with a cloth gives cast iron a natural patina-like appearance odourless   Very effective, the cream is applied in small quantities over the entire surface. Polish with a dry cloth.

Handbellow ø 20 cm, long ash wood, with leather total length approx. 60 cm   Our hand bellows are not a mass product. They are made in a small, traditional manufactory by hand.   All individual parts are made there and, last but not least, like 100 years ago, the leather is nailed to the wood by hand and the metal tip is attached to the head of the bellows.

  Finest PTFE particles (also known as Teflon™)

    Ballistol Ceramic Dry Lubricant is distinguished by its white, dry film, completely free of oil, grease, or silicone. It is universally applicable to all materials and withstands extreme temperatures from -55 °C to +1,000 °C. This provides a long-lasting and clean lubrication solution that guarantees optimal performance even under the toughest conditions.   Our ceramic dry lubrication is ideal for static, sliding, and rolling friction applications and is versatilely used in:   Rollers, bearings, and slides Guide rails Cable pulleys Oven slides and telescopic guides Gears and plastic components   Application: Shake well before use. Spray onto the parts or surfaces to be lubricated or made sliding from a distance of 10–25 cm and allow to dry for a few minutes.

  Typical ranges of application:   Troubleshooting of electrical components Testing thermostats and termperature sensors as well as engine components such as carburetors and injection systems For repair purposes in industry For assembly of fittings with tightest tolerances For cooling of transistors. resistors and silicium diodes For shock freezing of rubber, foils and sticky residues, also for the remocal of chewing gum Prevents heat damage during brazing and soldering processes

  guarantees an application field from -100 to 1000 °C   provides sustained protection against corrosion, sealing, wear and seizing. It facilitates smoother connections for threads and clearances, prevents contact corrosion in differing metals, guarantees an application field from -100 to 1000 °C and is highly pressure resistant.

    Long time rust protection, for lubricating thread machines / cutting machines   Ideal for long-therm preservation, even at high air humidity and aggressive ambient air Contains no waxes

  with lid + clamping ring   ideal for our hardening oil.   Properties: bright inside/outside temperature resistant with carrying handle slightly conical shape, therefore stackable

  stable brand quality, internal steel spring, with angular measure A yardstick should not be missing in any pocket. Made of beech wood in a robust construction. 200 cm total length with internal steel springs. These ensure a long service life.   Other features: Double-sided cm / mm graduation on both edges of the scale clearly recognizable graduation angular measure Accuracy class III